[Coco] Possible CoCo3FPGA Analog board run

[Brendan Donahe]

Ed, I have ordered a DE1 board and would like to buy an analog board from
you, as well.

Thanks,
Brendan

On Thu, Oct 19, 2017 at 8:39 PM, Zippster <zippster278 at gmail.com> wrote:

> Ok Rob, I’ll put you on the list.
>
> I haven’t been over on the Yahoo group for a while…
>
> - Ed
>
>
> > On Oct 19, 2017, at 8:37 PM, Rob Rosenbrock <bester at adamswells.com>
> wrote:
> >
> > I'm in that group as well, and expressed interest
> >
> > Sent from my iPad
> >
> >> On Oct 19, 2017, at 7:12 PM, Bill Pierce via Coco <coco at maltedmedia.com>
> wrote:
> >>
> >> Ed, there are several people on the Coco3FPGA group showing interest as
> well. Some do not subscribe to this list (yet), so you may want to repost
> this there.
> >>
> >>
> >>
> >>
> >>
> >> Bill Pierce
> >> "Charlie stole the handle, and the train it won't stop going, no way to
> slow down!" - Ian Anderson - Jethro Tull
> >>
> >> My Music from the Tandy/Radio Shack Color Computer 2 & 3
> >> https://sites.google.com/site/dabarnstudio/
> >> Co-Contributor, Co-Editor for CocoPedia
> >> http://www.cocopedia.com/wiki/index.php/Main_Page
> >>
> >> E-Mail: ooogalapasooo at aol.com
> >>
> >>
> >>
> >>
> >>
> >> -----Original Message-----
> >> From: Zippster <zippster278 at gmail.com>
> >> To: CoCoList for Color Computer Enthusiasts <coco at maltedmedia.com>
> >> Sent: Thu, Oct 19, 2017 5:26 pm
> >> Subject: [Coco] Possible CoCo3FPGA Analog board run
> >>
> >> Hello everyone,It’s come to my attention that there may be enough
> demand to produce anotherrun of analog boards for the CoCo3FPGA project.
> It’s been a little over a yearsince the first run was made, and it seems it
> may be time for another.The Analog board attaches to the DE1 FPGA unit
> through the two GPIO headersand adds the following hardware to the
> CoCo3FPGA…An additional serial port (DB9), Wi-fi module, RTC clock module,
> 2 Joystick ports,4MB of additional RAM, and an expansion header with the
> remaining unused GPIOpins (and power/ground) is added to the CoCo3FPGA
> system.Here’s a page on them from my website to see what they look like…<
> https://sites.google.com/site/thezippsterzone/coco-3-fpga <
> https://sites.google.com/site/thezippsterzone/coco-3-fpga>>These would
> come complete with a new set of standoffs and new top plate just as the
> earlier run and will probably be around $100 per set depending on the size
> of the run.If I can get at least 20 names we can make a go of it.Please let
> me know if you’re interested.Thanks,- EdInterest list - 10/19/17John
> BGrumpyxJerry AdamsJim Veneskey-- Coco mailing listCoco at maltedmedia.comhttps
> ://pairlist5.pair.net/mailman/listinfo/coco
> >>
> >> --
> >> Coco mailing list
> >> Coco at maltedmedia.com
> >> https://pairlist5.pair.net/mailman/listinfo/coco
> >
> >
> > --
> > Coco mailing list
> > Coco at maltedmedia.com
> > https://pairlist5.pair.net/mailman/listinfo/coco
>
>
> --
> Coco mailing list
> Coco at maltedmedia.com
> https://pairlist5.pair.net/mailman/listinfo/coco
>