[Coco] The ultimate VCC hard disk image using EmuDsk

Thu Nov 12 18:42:48 EST 2015

Thanks Bill and Barry!

I have liftoff. After performing the steps indicated and doing a hard reset I got I got a menu screen whose option 6 was to go to disk basic. I did that and typed in dos 255 and NitrOS9 came up.

I entered pwd and Enter, and got the prompt:

{Term|02}/DD:

But when I entered pwd<Enter> the screen displayed this:

{Term|02}/DD:   }

Where the p, w and d echoed as spaces and the Enter key echoed as "}". I tried backspace, but this echoed as "x".

-----Original Message-----
From: Bill Pierce via Coco <coco at maltedmedia.com>
To: coco <coco at maltedmedia.com>
Cc: Bill Pierce <ooogalapasooo at aol.com>
Sent: Thu, Nov 12, 2015 2:32 pm
Subject: Re: [Coco] The ultimate VCC hard disk image using EmuDsk

First, you must have the "harddrive.dll" in slot 3 (along with "fd502.dll" in
slot 4)

2nd you must then mount the vhd image in "HD Drive 0" slot that is
created in the "Cartridge" menu after mounting the "harddrive.dll"

3rd, you
must be using the "rgbdos.rom" in "Cartridge/FD-502 Config/DosImage" and check
"RGB Dos".

You are currently (according to your stated setup) not even using
the hard drive emulation so therefore cannot use a VHD at all, only "dsk"
images. The FD-502 disk controller emulates the standard RS floppy disk
controller, not a hard drive controller. That only gives you DECB which cannot
access HDs (or VHDs). RGBDOS is set up to use VHDs with 256 vitrual RSDOS disks
and an OS9 partiton. You must follow the above steps to use the
VHD.

Instructions for using RGBDOS are basically the same as for HDBDOS for
which the manual can be found on the Cloud9 site un "Support".

Bill
Pierce
"Charlie stole the handle, and the train it won't stop going, no way to
slow down!" - Ian Anderson - Jethro Tull

My Music from the Tandy/Radio Shack
Color Computer 2 & 3
https://sites.google.com/site/dabarnstudio/
Co-Contributor,
Co-Editor for CocoPedia
http://www.cocopedia.com/wiki/index.php/Main_Page
Global
Moderator for TRS-80/Tandy Color Computer
Forums
http://www.tandycoco.com/forum/

E-Mail: ooogalapasooo at aol.com

-----Original Message-----
From: Salvador Garcia
<ssalvadorgarcia at netscape.net>
To: coco <coco at maltedmedia.com>
Sent: Thu, Nov
12, 2015 3:14 pm
Subject: Re: [Coco] The ultimate VCC hard disk image using
EmuDsk

Thank you Richard! Much appreciated!

Tried that, no space and got
same
result.

I know I am doing something stupid, or maybe it is because I am
not
doing it. I also tried dir 255
and got ?DN ERROR.

Tried dir 0. Got back
the
listing for the floppy that I have mounted at that location.

I poked
around
some more. info follows (whether it is relevant or not, I don't
know)

Menu
option Cartridge/MPI Slot n

4: FD502 26-3133
3: Empty
2:
Orchestra 90
26-3143
1: Empty

Configuration:

Set to use hitachi
6309
2MB
RAM

Salvador

-----Original Message-----
From: Richard E.
Crislip
<rcrislip at neo.rr.com>
To: coco <coco at maltedmedia.com>
Sent: Thu, Nov 12,
2015
1:51 pm
Subject: Re: [Coco] The ultimate VCC hard disk image using
EmuDsk

On
Thu, 12 Nov 2015 13:32:26 -0500
Salvador
Garcia
<ssalvadorgarcia at netscape.net>
wrote:

> I was curious, so I downloaded
the ZIP
file. 
> 
> 
> The txt file
says type in DOS 255.
> 
> 
> I started Vcc,
mounted
the image on HD0 and
entered the above command.
> 
> 
> I got ?SN
error
> 
> 
>
This is my first
venture into doing anything with Vcc and I
basically
> guessed
at the above
steps.
> 
> 
> Is there a guide that I can
follow so that I won't
be completely
lost?
> 
> 
> After DOS 255 works, what
then? Any references to
material that
I
> read up on would be helpful.
> 
> 
>
Barry, thanks for putting
this
together. I have no clue what I am
> getting
into, but am excited about
it.
:-)
> 
> 
> Thanks!
> Salvador
> 
> 
> 
> 
>
-----Original Message-----
>
From:
Barry Nelson
<barry.nelson at amobiledevice.com>
> To:
coco
<coco at maltedmedia.com>
> Sent: Thu,
Nov 12, 2015 9:51 am
> Subject: Re:
[Coco]
The ultimate VCC hard disk image
using EmuDsk
> 
> 
> The latest version
of this
disk image is now available
from
>
http://www.colorcomputerarchive.com/
> 
> The
link directly to the
page
is
>
http://www.colorcomputerarchive.com/coco/Virtual%20Hard%20Drives/NitrOS-9%20L2%20V3.3.0/
>

>
This
>
hard disk image should work with either VCC or MESS. It boot using
>
the
EMUDisk
driver, and so does not require a DriveWire server to
> run. It will
NOT
boot on
a real CoCo, nor will it boot from
> DriveWire, however, it can
be
mounted as a
second disk and the
> programs can be run. If there is interest,
I
could make a
CoCo SDC
> and/or a Glenside IDE version.
> 

That should be
DOS255
no
space.

--

Coco
mailing
list
Coco at maltedmedia.com
https://pairlist5.pair.net/mailman/listinfo/coco

--

Coco
mailing
list
Coco at maltedmedia.com
https://pairlist5.pair.net/mailman/listinfo/coco

-- 
Coco mailing
list
Coco at maltedmedia.com
https://pairlist5.pair.net/mailman/listinfo/coco