[Coco] DriveWire is just a hobby (Was: DW4 on MAc & Linux)

[Al Hartman]

BTW... Could you tell me which files in the ZIP re the ROM files I need to 
burn for a Coco 3 and Coco 2 Disk Controller? Are there different ones for a 
Drivepak?

-[ Al ]-

-----Original Message----- 
From: Bill Pierce
Sent: Thursday, September 26, 2013 6:57 PM
To: coco at maltedmedia.com
Subject: Re: [Coco] DriveWire is just a hobby (Was: DW4 on MAc & Linux)


Al, the rom files have no load address. They are just direct dumps. They are 
not meant to be loaded into the Coco. Only by the burner software.

Bill Pierce
My Music from the Tandy/Radio Shack Color Computer 2 & 3
https://sites.google.com/site/dabarnstudio/
Co-Webmaster of The TRS-80 Color Computer Archive
http://www.colorcomputerarchive.com/
Co-Contributor, Co-Editor for CocoPedia
http://www.cocopedia.com/wiki/index.php/Main_Page
E-Mail: ooogalapasooo at aol.com




-----Original Message-----
From: Al Hartman <alhartman6 at optonline.net>
To: CoCoList for Color Computer Enthusiasts <coco at maltedmedia.com>
Sent: Thu, Sep 26, 2013 6:45 pm
Subject: Re: [Coco] DriveWire is just a hobby (Was: DW4 on MAc & Linux)


DOH!!!!!

Thanks Art!

Do you know of a program that can look at a binary file and tell what
address it is meant to load to?

Because I don't know where the ROM files in the Drivewire image are going to
load to.

-[ Al ]-

-----Original Message----- 
From: Arthur Flexser
Sent: Thursday, September 26, 2013 4:24 PM
To: CoCoList for Color Computer Enthusiasts
Subject: Re: [Coco] DriveWire is just a hobby (Was: DW4 on MAc & Linux)

Al, a trick I use to avoid having to calculate offsets is this:

Say you want to move a file XYZ.BIN that would normally load at $7E00
so that it loads at $2000 instead.  Just issue this command:

LOADM"XYZ",&H2000-&H7E00

Let the computer worry about the offset calculation!

Art

On Thu, Sep 26, 2013 at 4:02 PM, Al Hartman <alhartman6 at optonline.net>
wrote:

> I need to burn an HDB-DOS ROM for my J&M Controller. I just need to know
> which file to use, and how to get it to the correct memory area so I can
> burn it to an EPROM on my Coco. I'd like to burn one for the Coco 2, and
> another for the Coco 3.
>
> All the Coco DECB manuals are cryptic on using the offset parameter of the
> LOADM command, and I have to figure out where the ROM file is set to load
> to, so I can calculate the offset and save it to tape for burning. I have
> an
> EPROM eraser coming in case I screw up. My old one has disappeared.
>
> ADOS made it seem so easy... LOL!
>

--
Coco mailing list
Coco at maltedmedia.com
http://five.pairlist.net/mailman/listinfo/coco


--
Coco mailing list
Coco at maltedmedia.com
http://five.pairlist.net/mailman/listinfo/coco



--
Coco mailing list
Coco at maltedmedia.com
http://five.pairlist.net/mailman/listinfo/coco